Search

Your Search for "foam cutter" results:

Summer Sand Castle

In a well-ventilated, newspaper-covered area (inside a cardboard box), spray the clay pot saucer with primer. Let dry. Then spray with two coats white and let dry.  On top of the block, use a pencil or marker and ruler to draw a square 1/2″ in from the edges. Use Foam Cutter along those lines, going […]

Spring Blooms

Use Foam Cutter to trim off squared edges of block into rounded cube. In a well-ventilated, newspaper covered area (inside cardboard box) spray Foam Block with adhesive spray. Insert two toothpicks into either side of Foam Block to be able to hold block to lift out of box. Set block onto  paper plate in work […]

Winter Wedding Table Arrangement

Use foam cutter to trim dry foam sheet to fit inside tray. Use glue gun to attach to bottom. Press in place until firmly set. Depending on weight of floral wire, use Floral Shears or Wire Cutter to trim floral stems to approximately 1-1/ 2″ lengths, as you go along. Start with one large Daisy […]

Faux Birch Christmas Tree

Cut three 18″ x3″ pieces from the foam sheet.  Save the remaining piece for a future project.  Glue the three pieces on top of one another to create a 3″ x3″ x18″ piece of foam.  Use the foam cutter to trim the corners along the sides of the foam piece.  Taper it slightly towards the […]

Hanukkah Arrangement

Wash and dry vase.  Use foam cutter to cut foam rod to 9″ long and glue at bottom into vase. Insert florals into foam in next steps.  Use wire cutter to cut florals as directed. Insert evergreen bush into center of vase, and evergreen/bell spray at each side.  Cut apart pine spray, and add to […]

Christmas Countdown

Use the foam cutter to cut the foam sheet in half. You should have two 12×18″ pieces. Set one piece aside. and Cut 3″ off the 18″ side of the second piece. You should have a 3″ x18″ piece and a 9″ x18″ piece. Use the spatula to apply the Smooth Finish® to the top […]

Merry Christmas Faux Pallet Art

Lay the ruler across the 12″ end of the foam sheet. Make a mark every 4″ with the black marker to create the boards. Do this at both ends of both foam sheets. Lay the ruler even with the marks at the top and bottom of the foam sheet. Hold the ruler tightly to the […]

“Believe”

Use the foam cutter or serrated knife to cut the cubes in half. The cubes should measure 5” tall x 5” wide x 2.5” thick. For the three taller letters, glue two half blocks stacked one on top of the other. The stacked blocks will measure 10” tall x 5” wide x 2.5” thick. Cut […]

Yarn Monsters

Cut the 2” balls and the 1” balls in half using the foam cutter. To create the feet, glue three 1” half balls side by side to the front of a 2” half ball. Repeat to create all four feet. Paint the feet purple and set them aside to dry. Wrap the 4” and 5” […]

Mummy Monsters

Cut one 2” x 12” piece and two 6” x 9” pieces from one of the foam sheets using the foam cutter. Cut one 3”x6” piece for the mini monster. Glue the 2”x12” piece to the end of one of the 18” sheets. This is the taller blue monster. Glue the 9” edge of the […]

Fall Floral Sconces

Use foam cutter to cut foam balls in half. Set both halves, cut side down, in a well-ventilated, newspaper-covered area (inside box) — spray ball halves with spray adhesive. Remove from box and cover with Spanish Moss. Apply hot glue to the top of the rim on each candle sconce and set the ball half’s […]

Ghost Group

For each ghost, refer to the materials list for measurements. (Note: If making all three ghosts, make sizes more proportionate by trimming about 1″ off the top of the large cone only.) For each, use Foam Cutter to cut a hole in Foam Ball (head) to fit onto Foam Cone (body). Remove the head, insert […]